Обновление основого ПО контроллера (перед установкой не забываем читаем Release Notes):
>transfer download mode tftp >transfer download datatype code >transfer download serverip 192.168.1.103 >transfer download filename AIR-CT2500-K9-7-6-100-0.aes >transfer download start
После успешной заливки нужно ребутнуть систему.
Field Upgrade Software
Field Upgrade Software (FUS) это пакет обновления AES для связанных с системой компонентов. Пакет используется для обновления таких вещей как bootloader, field recovery image, FPGA/MCU.
Сейчас на контроллере основной код версии 7.6.100.0 а Field Recovery Image 1.0.0
(Cisco Controller) >show sysinfo
Manufacturer’s Name………………………… Cisco Systems Inc.
Product Name………………………………. Cisco Controller
Product Version……………………………. 7.6.100.0
Bootloader Version…………………………. 1.0.18
Field Recovery Image Version………………… 1.0.0
Firmware Version…………………………… PIC 16.0
Теперь заливаем на контроллер AIR-CT2500-K9-1-9-0-0-FUS.aes по tftp (Release notes 1.9.0.0)
>transfer download mode tftp >transfer download datatype code >transfer download serverip 192.168.1.103 >transfer download filename AIR-CT2500-K9-1-9-0-0-FUS.aes >transfer download start
Mode............................................. TFTP Data Type........................................ Code TFTP Server IP................................... 192.168.1.103 TFTP Packet Timeout.............................. 6 TFTP Max Retries................................. 10 TFTP Path........................................ TFTP Filename.................................... AIR-CT2500-K9-1-9-0-0-FUS.aes
This may take some time. Are you sure you want to start? (y/N) y TFTP Code transfer starting. TFTP receive complete... extracting components. Checking Version Built. Image version check passed. Writing new Field Upgrade Software RTOS to flash disk. Writing new Offline Diagnostic Image to flash disk. Writing new Field Recovery Image to flash disk. Executing fini script. File transfer is successful the controller for update to complete Optionally, pre-download the image to APs before rebooting to reduce network downtime.
(Cisco Controller) >reset system ?
The system has unsaved changes. Would you like to save them now? (y/N) y
Configuration Saved! System will now restart!
После этого контроллер ушел в себя, 30 минут ждал его загрузки. И ничего. Подключил консоль, но ответа не было. Перегрузил по питанию и процесс пошел.
WLCNG Boot Loader Version 1.0.20 (Built on Jan 14 2014 at 11:40:45 by cisco) Board Revision 0.0 (SN: PSZ172701NY, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz data rate) CPU Cores: 4 DRAM: 1024 MB Flash: 32 MB Clearing DRAM........ done Network: octeth0', octeth1, octeth2, octeth3 ' - Active interface E - Environment MAC address override CF Bus 0 (IDE): OK IDE device 0: - Model: 1GB CompactFlash Card Firm: CF B612J Ser#: A191103068A12d5DA9gl - Type: Hard Disk - Capacity: 977.4 MB = 0.9 GB (2001888 x 512)
Press <ESC> now to access the Boot Menu...
Loading primary image (7.6.101.2) 100%
6394630 bytes read Launching... Launching images... init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary starting pid 688, tty '': '/etc/init.d/rcS'
Field Upgrade Software
Bundles included in this upgrade:
- Bootloader - Field Recovery image - Offline Diagnostic image
****************************************************************** * Please make sure POWER SUPPLY is always ON during this period. * * Lost POWER will completely kill this unit and not recoverable. * ******************************************************************
Start soon ...
==================== Checking for Field recovery image upgrade
Field Recovery Image upgrade ...
Field recovery image Current version 7.6.101.1 is up-to-date. Answer "y" below will force upgrade to run again.
Upgrade will start in 30 sec, press (y) to start immediately else press any key to ABORT !!.
Timeout, starting upgrade.
****************************************************************** * Please make sure POWER SUPPLY is always ON during this period. * ******************************************************************
Erasing Flash (estimated 49 seconds) ...
Writing to flash (estimated 761 seconds) ...
All upgrades done. System reboot ... Restarting system.
WLCNG Boot Loader Version 1.0.20 (Built on Jan 14 2014 at 11:40:45 by cisco) Board Revision 0.0 (SN: PSZ172701NY, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz data rate) CPU Cores: 4 DRAM: 1024 MB Flash: 32 MB Clearing DRAM........ done Network: octeth0', octeth1, octeth2, octeth3 ' - Active interface E - Environment MAC address override CF Bus 0 (IDE): OK IDE device 0: - Model: 1GB CompactFlash Card Firm: CF B612J Ser#: A191103068A12d5DA9gl - Type: Hard Disk - Capacity: 977.4 MB = 0.9 GB (2001888 x 512)
Press <ESC> now to access the Boot Menu...
Loading primary image (7.6.100.0) 100%
36109609 bytes read Launching... Launching images... init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary starting pid 688, tty '': '/etc/init.d/rcS' Detecting Hardware ... Installing ether-pow driver - 0x6008 starting pid 831, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar' Setting up ZVM Exporting LD_LIBRARY_PATH
Cryptographic library self-test....passed! XML config selected Validating XML configuration Read HA Config before validation octeon_device_init: found 1 DPs /dev/fpga: No such device or address readCPUConfigData: cardid 0x6060001 Cisco is a trademark of Cisco Systems, Inc. Software Copyright Cisco Systems, Inc. All rights reserved.
Cisco AireOS Version 7.6.100.0 Firmware Version PIC 16.0
Initializing OS Services: ok Initializing Serial Services: ok Initializing Network Services: ok Initializing Licensing Services: License daemon start initialization..... ok
License daemon running..... Starting Statistics Service: ok Starting ARP Services: ok Starting Trap Manager: ok Starting Network Interface Management Services: ok Starting System Services: ok Starting FIPS Features: ok : Not enabled Starting Fastpath Hardware Acceleration: ok Starting Fastpath Console redirect : ok Starting Fastpath DP Heartbeat : ok Fastpath CPU0.00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok Fastpath CPU0.00: Initializing last packet received queue. Num of cores(2) Fastpath CPU0.00: Init MBUF size: 1856, Subsequent MBUF size: 2040 Fastpath CPU0.00: Core 0 Initialization: ok Fastpath CPU0.00: Initializing Timer... Fastpath CPU0.00: Initializing Timer...done. Fastpath CPU0.00: Initializing Timer... Fastpath CPU0.00: Initializing NBAR AGING Timer...done. Fastpath CPU0.01: Core 1 Initialization: ok Starting Switching Services: ok Starting QoS Services: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting DNS Services: ok Starting Licensing Services: ok Starting Redundancy: ok Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok Starting Security Services: ok Starting Policy Manager: ok Starting Authentication Engine: ok Starting Mobility Management: ok Starting Capwap Ping Component: ok Starting AVC Services: ok Starting Virtual AP Services: ok Starting AireWave Director: ok Starting Network Time Services: ok Starting Cisco Discovery Protocol: ok Starting Broadcast Services: ok Starting Logging Services: ok Starting DHCP Server: ok Starting IDS Signature Manager: ok Starting RFID Tag Tracking: ok Starting RF Profiles: ok Starting Power Supply and Fan Status Monitoring Service: ok Starting Mesh Services: ok Starting TSM: ok Starting CIDS Services: ok Starting Ethernet-over-IP: ok Starting DTLS server: enabled in CAPWAP Starting CleanAir: ok Starting WIPS: ok Starting SSHPM LSC PROV LIST: ok Starting RRC Services: ok Starting SXP Services: ok Starting Alarm Services: ok Starting FMC HS: ok Starting IPv6 Services: ok Starting Config Sync Manager : ok Starting Hotspot Services: ok Starting Portal Server Services: ok Starting mDNS Services: ok Starting Management Services: Web Server: CLI: Secure Web: ok
(Cisco Controller)
Enter User Name (or 'Recover-Config' this one-time only to reset configuration to factory defaults)
Процесс обновления связанных с системой компонентов длился 15 минут. Смотрим на что обновились.
User: admin
Password:*********
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller Product Version.................................. 7.6.100.0 Bootloader Version............................... 1.0.20 Field Recovery Image Version..................... 7.6.101.1 Firmware Version................................. PIC 16.0